preliminary gan mmic gm2 0 0 22 0 10 d korean facilities : 82 - 31 - 8069 - 3036 / rfsales@rfhic.com all specifications may change without notice us facility : 919 - 677 - 8780 / sales@rfhicusa.com 1 / 5 ver s i o n 0. 1 product features application s ? 2 0 ~ 22 g hz frequency range ? 10w gan hemt mmic ? 24 % efficiency at psat ? up to 28v supply voltage ? 50ohm matched input/output ? die size 3.4 x 3.4 x 0.1 mm ? s at c o m ? p oint to point radios ? point to multipoint radios description gm2 0 0 22 0 10 d is a balanced 3 - stage monolithic gan hemt amplifier for satcom and point to point or point to multipoint radios application . this mmic is fully matched to 50 ohms with integrated dc blocking capacitors on rf ports . t his mmic ty pically provides 25 db of small signal gain and 40dbm of saturated output power , 2 4 % of efficiency electrical specifications parameter unit min typ max condition frequency g hz 20 - 22 - gain db 23 25 - - power gain db - 22 - cw input return loss db - -10 - - output return loss db - -10 - - peak output power dbm - 40 - cw efficiency % - 24 - cw dc current ma - 10 00 - vdd = 28. 0v note 1. test conditions unless otherwise noted. t=25 , vdd= 28 v, 50 ? system absolute maximum ratings parameter unit min typ max drain voltage vdc - - 35 gate voltage vdc - 5.5 - 0 operating temperature -40 - +85 storage temperature -55 - +150 mounting temperature - - 300
preliminary gan mmic gm2 0 0 22 0 10 d filii 2 31 0 303 / li.m all iii m i i u fili 1 77 70 / li.m 2 / 5 ver s i o n 0. 1 typical performance @ vdd= 28 v, i d s = 100 0ma, t=25 frequency pout (dbm), pae (%), gain (db) pout, pae, gain vs. frequency input power (dbm) pout (d bm), gain(db) pout (dbm), gain(db) input power (dbm) pae (%) pout, pae, gain vs. input power pout, pae, gain vs. input power pae (%) input power (dbm) pout (dbm), gain(db) pout (dbm), gain(db) input power (dbm) pae (%) pae (%) pout , pae, gain vs. input power pout, pae, gain vs. input power
preliminary gan mmic gm2 0 0 22 0 10 d filii 2 31 0 303 / li.m all iii m i i u fili 1 77 70 / li.m 3 / 5 ver s i o n 0. 1 block diagram die dimensions (mm) dc/gnd bond pad : 100 x 100 um rf bond pad : 100 x 100 um die thickness : 0.10mm
preliminary gan mmic gm2 0 0 22 0 10 d filii 2 31 0 303 / li.m all iii m i i u fili 1 77 70 / li.m 4 / 5 ver s i o n 0. 1 assembly diagram ground is backside of die vg & vd connection must be biased from both sides. recomme nded solder is ausn(80/20) solder evaluation board d imension 0.05mm gap 0.7mil gold wire rf_in rf_out vg1 /2 vd1 /2 vg3 vd 3 vg1 /2 vd1 /2 vg3 vd 3 vg1/2 /3 vd1/2/3 nc vg1/2 /3 vd1/2/3 nc
preliminary gan mmic gm2 0 0 22 0 10 d filii 2 31 0 303 / li.m all iii m i i u fili 1 77 70 / li.m 5 / 5 ver s i o n 0. 1 revision history part number release date version m odification data sheet status gm 200 22 0 10 d 201 7. 11 . 27 0.1 initial release preliminary rfhic corporation reserves the right to make changes to any products herein or to discontinue any product at any time without notice. while product specifications have been thoroughly examined for reliability, rfhic corporation strongly recommends buyers to verify that the information they are using is accurate before ordering. rfhic corporation does not assume any liability for the suitability of its products for any particular purpose, and disclaims any and all liability, including without limitation consequential or incidental damages. rfhic products are not intended for use in life support equipment or application where malfunction of the product can be expected to result in personal injury or death. buyer uses or sells such products for any such unintended or unauthorized application, buyer shall indemnify, protect and hold rfhic corporation and its directors, officers, stockholders, employees, representatives and distributors harmless against any and all claims arising out of such unauthorized use. sales, inquiries and support should be directed to the local authorized geographic distributor for rfhic corporation. for customers in the us, please contact the us sales team at 919- 677-8780 . for all other inquiries, please contact the international sales team at 82 -31-8069-3036
|
